Skip to main content Skip to first level navigation

RICOH imagine. change.

RICOH ELECTRONIC DEVICES CO., LTD.

Skip to main content First level navigation Menu
Main content

R5480 Series
1-Cell Li-ion Battery Protection IC with RSENS pin

Product Specifications

The R5480 is a high voltage tolerance CMOS-based protection IC for over-charge/discharge and over-current of rechargeable one-cell Lithium-ion (Li+)/Lithium polymer battery. The R5480 can detect over-charge/discharge of Li+ one-cell and excess load current and charge current, further, include a short circuit protector for preventing large external short circuit current. The R5480 consists of four voltage detectors, a reference unit, a delay circuit, a short circuit detector, an oscillator, a counter, and a logic circuit.

When the R5480 detects over-charge or over-charge current, the output of COUT pin switches to “L” level, of the charger’s negative pin level after the internal fixed delay time. When the R5480 detects over-discharge or excess discharge current, the output of DOUT pin switches to “L” level after the internal fixed delay time.

After detecting over-charge or excess charge current, the R5480 can be reset and the output of COUT becomes “H” after the charger is disconnected from the battery pack, and the cell voltage becomes lower than over-charge detector threshold.

However, depending on the characteristics of external components such as MOSFETs, release conditions may be not enough just removing a charger from the battery pack. In that case, a kind of load must be set to release the over-charge detect.

If a charger is continuously connected to the battery pack, even if the cell voltage becomes lower than over-charge detector threshold, over-charge state is not released.
After detecting over-discharge voltage, connect a charger to the battery pack, and when the battery supply voltage becomes higher than over-discharge detector threshold, the R5480 is released and the voltage of DOUT pin becomes “H”. If the battery is discharged to 0V, recharge current is not acceptable. Once after detecting excess discharge-current or short circuit, the R5480 is released and DOUT level becomes “H” with detaching a battery pack from a load system. After detecting over-discharge, supply current is kept extremely low by halting internal circuits' operation.

When the output of COUT is "H", by setting the V- pin between -3.0V and the delay shortening mode voltage (Typ. -2.0V), the output delay can be shortened. Especially, the delay time of over charge detector can be reduced into approximately 1/100. Thus, testing time of protector circuit board can be reduced. Output type of COUT and DOUT is CMOS.

FEATURES

Manufactured with High Voltage Tolerant Process Absolute Maximum Rating 30 V
Low supply current Supply current (At normal mode) TYP. 4.0 µA
Standby current MAX. 0.1 µA
High accuracy detector threshold Over-charge detector ±20 mV
Over-discharge detector ±35 mV
Excess discharge-current detector ±15%
Excess charge-current detector ±15%
Variety of detector threshold Over-charge detector threshold 4.1 V ~ 4.5 V step of 0.005 V
Over-discharge detector threshold 2.1 V ~ 3.0 V step of 0.005 V
Excess discharge-current threshold 0.030 V ~ 0.048 V step of 0.001 V
Excess charge-current threshold -0.030 V ~ -0.020 V step of 0.001 V
Internal fixed Output delay time Over-charge detector Output Delay 1.0 s
Over-discharge detector Output Delay 20 ms
Excess discharge-current detector Output Delay 12 ms
Excess charge-current detector Output Delay 16 ms
Short Circuit detector Output Delay 250 µs
Output Delay Time Shortening Function At COUT is "H", if V- level is set at –2.0V, the Output Delay time of detect the over-charge and over-discharge can be reduced. (Delay Time for over-charge becomes about 1/100 of normal state.)
Conditions for release over-charge detector Latch type
Conditions for release over-discharge detector Latch type
0V-battery charge option unacceptable
Ultra Small package DFN(PLP)1414-6

Tap to see the table


R5480 Series for Consumer

APPLICATIONS

  • Li+ / Li Polymer protector of over-charge, over-discharge, excess-current for battery pack
  • High precision protectors for smart-phones and any other gadgets using on board Li+ / Li Polymer battery

DOCUMENT/CONTACT

Purchase

Technical Support

Package*1 Reliability*2
DFN(PLP)1414-6 R5480K

*1: The package file includes package dimensions, taping specifications, taping reels dimensions, power dissipations, and land pattern (foot pattern).
*2: Reliability file includes a reliability test report and a reflow profile.

Inquiry about products

Technical Support

Inquiries (SSL Form)

Inquiry about business

Purchase, Request for Samples and Documents

Distributors

Sample Online

Online Distributors